|
Welcome to BotBlox Technical Support Forum! :wave:
|
|
0
|
892
|
July 28, 2023
|
|
Testing Ubiswitch with External PHY
|
|
5
|
25
|
October 21, 2026
|
|
Can SwitchBlox be stacked to create a 10-port switch?
|
|
0
|
7
|
October 20, 2026
|
|
Puck Edge FAQ: management, power, weight and included cables
|
|
0
|
5
|
October 20, 2026
|
|
UbiSwitch Module and Baseboard Mini: pressure tolerance and immersion in MIDEL 7131
|
|
0
|
6
|
October 20, 2026
|
|
RouterCore Module and RouterCore Nano: NAT, port expansion, dimensions and connectors
|
|
0
|
7
|
October 20, 2026
|
|
Switchblox's rugged memory
|
|
1
|
13
|
October 20, 2026
|
|
GigaBlox Nano: PicoBlade pinout, carrier-side LSHM numbering and RJ45 cable mapping
|
|
0
|
18
|
October 9, 2026
|
|
Why is a 16 pin header suggested for use with SwitchBlox Rugged, which has an 18 pin stacking header?
|
|
5
|
97
|
October 7, 2026
|
|
Puck Mini: board-only evaluation, LED removal and power consumption
|
|
3
|
30
|
October 7, 2026
|
|
Minimum input voltage for active PoE on the Universal PoE Module
|
|
3
|
25
|
October 3, 2026
|
|
Use PTP protocol to generate PPS signal (one pulse per second)
|
|
2
|
34
|
October 2, 2026
|
|
SwitchBlox Rugged vs. Industrial: Temperature ratings, PoE and choosing the right board
|
|
0
|
32
|
September 28, 2026
|
|
PCBA Inspection Standard: Is the GigaBlox assembled and inspected in accordance with IPC-A-610 Class 2 (or Class 3)?
|
|
1
|
31
|
September 25, 2026
|
|
SwitchBlox Rugged : data loss and auto-negotiation issues
|
|
3
|
120
|
September 25, 2026
|
|
GigaBlox BB-GGB-C-3: What is R4’s value, and where does U1 pin 3 connect?
|
|
0
|
29
|
September 19, 2026
|
|
Can I swap Ethernet pairs on UbiSwitch to simplify PCB routing?
|
|
0
|
24
|
September 19, 2026
|
|
GigaBlox Revision C: NDAA part number and applicable datasheet
|
|
0
|
23
|
September 19, 2026
|
|
QuadDrive 80A: Weight, power distribution, voltage spikes and heatsink requirements
|
|
0
|
23
|
September 19, 2026
|
|
Puck Edge: Why do 1G devices fail to communicate through the 10G ports?
|
|
0
|
36
|
September 18, 2026
|
|
What changed between GigaBlox revisions BB-GGB-C-CO2 and BB-GGB-C-3?
|
|
0
|
26
|
September 10, 2026
|
|
Troubleshooting UDP packet loss and intermittent link drops on SwitchBlox
|
|
0
|
29
|
September 10, 2026
|
|
Accesing rugged som
|
|
6
|
87
|
September 9, 2026
|
|
Can I substitute the Ethernet transformer and common-mode choke in a BotBlox reference design?
|
|
0
|
27
|
September 7, 2026
|
|
Can SwitchBlox Industrial convert a 12 V input to 24 V or 57 V passive PoE?
|
|
0
|
27
|
September 7, 2026
|
|
Updating UbiSwitch from BloxOSLite v1.0.x over UART
|
|
0
|
31
|
September 7, 2026
|
|
How to connect an external PHY to SerDes 10G interface
|
|
3
|
76
|
August 25, 2026
|
|
Connecting UbiSwitch directly to a 10GBASE-R CML SERDES interface
|
|
0
|
33
|
August 22, 2026
|
|
SwitchCore TX/RX Polarity and Schottky Diode Input Protection
|
|
0
|
35
|
August 21, 2026
|
|
Why Does a 100 Mbps Port Report a 10 Mbps Link?
|
|
0
|
35
|
August 21, 2026
|